H2S Analyser - SA4000-3

.

PRODUCT

H2S Analyser – SA4000-3

The H2S Analyser and Vapour Phase Processor (SA4015-0) are compact bench-top instruments, used to measure the total hydrogen sulphide (H2S) content of fuel oils, such as marine residual fuels, distillates and petroleum blend stocks. The H2S Analyser can measure H2S concentrations from 0 to 250 mg/kg (ppm) in the liquid phase.

H2S is efficiently purged from the test sample by a combination of heat and agitation, and is measured by a proprietary advanced gas specific detector. The instrument offers a cost effective solution for H2S measurement – no costly or hazardous chemicals are required and there is no need for analytical preparation by an experienced chemist.

request a quote

Do NOT CHANGE OR REMOVE THIS ELEMENT

H2S Analyser – SA4000-3

Spares and accessories

Features

Measurement range from 0-250 mg/kg H₂S (0-250 ppm H₂S) in the liquid phase
Vapour Phase Processor proven to eliminate effects of chemical interference
A non chemical method, no wet chemistry involved
Small lab bench footprint, fully portable operation
Suitable for monitoring residual marine fuel blends, Crude Oil, refinery feedstock components, cargoes & products in the distribution system
Critical Measurement method for Product Safety and Release

specifications

MEASUREMENT RANGE	0-250 mg/kg H2S in the liquid phase (0-250 ppm H2S)
H2S ANALYSER TEST TEMPERATURE	60 °C ±1 °C
VISCOSITY RANGE	Up to 3000 mm2/s
PRINCIPLE OF MEASUREMENT	Electro-chemical sensor
TEST DURATION	15 minute
SAMPLE SIZE	1 ml, 2 ml, 5 ml (depending on H2S concentration)
DILUENT VOLUME	20 ml
VOLTAGE	12 Vdc, supplied with universal A/C transformer
POWER	60 W max
COMPUTER INTERFACE	RS232
SIZE (HXWXD)	220 x 290 x 380 mm
WEIGHT	8 kg
CCCN CODE	Tariff 90268020

Manufacturers

show DATA — DO NOT CHANGE ID–

Document

H2S Analyser – SA4000-3

Industries

show DATA — DO NOT CHANGE ID–

Methods

show DATA — DO NOT CHANGE ID–

Spares and accessories for SA4000-3

H2S VPP Calibration Kit – SA4019-2

Calibration kit for use with the Vapour Phase Processor (SA4015-0).

H2S Airflow Calibration & Verification Kit (IP 570) – SA4011-0

Airflow calibration and verification kit for use with the H2S Analyser (SA4000-3).

H2S Static Calibration & Verification Kit – SA4001-2

H2S static calibration and verification kit for use with H2S Analyser (SA4000-3). Includes traceable verification gas, replacement regulator and a connection hose.

H2S Start up Kit for IP 570 (approx 20 tests) – SA4003-3

Start up kit for use with the H2S Analyser (SA4000-3) to perform IP 570 test. Allows approximately 20 tests.

H2S Vapour Phase Processor (VPP) – SA4015-0

The Vapour Phase Processor (VPP) is used with the H2S Analyser (SA4000-3) and removes components that may affect the accuracy of the results, such as toluene, xylene, thiols (mercaptans) and alkyl sulphides

H2S Liquid Trap (pack of 5) – SA4000-009

Pack of 5 liquid traps or use with the H2S Analyser (SA4000-3).

H2S Filters (pack of 50) – SA4000-003

Pack of 50 moisture/particulate filters for use with the H2S Analyser (SA4000-3).

Nylon filters for replacing dust filter, moisture filter and VPP dust filter.

H2S Syringes (pack of 200) – SA4000-007

Pack of 200 x 10 ml syringes for use with the H2S Analyser (SA4000-3).

H2S Consumables kit (200 tests) – SA4005-3

Consumables kit for use with the H2S Analyser (SA4000-3).

H2S Diluent 5 litres – SA4013-0

5 litres of diluent for use with the H2S Analyser (SA4000-3). 20 ml is typically required per test.

Calibrated Sensor for H2S Analyser – SA4000-201

Calibrated sensor for use with the H2S Analyser (SA4000-3). Valid for approximately 9 months depending on frequency of use (excluded from warranty). Please quote the serial number of the instrument when ordering.